Sie haben keine Artikel im Warenkorb.
On this page, I collect all information about the new Sculpfun S10 laser. The introduction has been postponed for some time, but now it is here. I have already been able and will test it and make the results available here. In particular, I would like to discuss the changes to the S9 and create corresponding instructions. The official introductory videos can be found here: YouTube. More reviews can be found at the bottom of the page. If you like video reviews, I recommend checking out the one from Dragoncut. The manual can be downloaded here.
S10 Module Installation (S9 frame)
A list of shopping links to the laser kit or the laser head can be found on the links / resources page.
The pump is not included in the scope of delivery, but is available separately (currently not yet, but soon). I tested it and is very quiet! Technical data of the pump:
The only disadvantage in my opinion is the air inlet that is at the bottom of the pump. It’s difficult to attach a hose there, in case you want to include the pump into an enclosure (I have bad experiences if the pump sucks in the dirty air within the enclosure; therefore I’d like to use air from the outside).
Yes, this will be possible shortly. It can also be mounted to the frame of the S6 / S9 laser.
Edit: Seems it arrived at the usual stores (AliExpress, Banggod etc.) now. Just do a quick search there.
Yes, this is no problem. Both mechanically and electrically, the heads are compatible. The power supplies (12V, 5A) also provide enough power.
The head can also be operated on many frames from other manufacturers (as long as the laser head is supplied with 12V and a 12V control signal). There is a fairly universal bracket supplied, if that does not fit, you have to help yourself.
Of course, it is not possible to give a universal answer to this question. In principle, I would say:
Here are a few of the official promotional images showing the features and scope of delivery. A frequently asked question is whether the Air Assist pump is also included, this is not the case. However, the Air Assist nozzle is including a hose. Except for the linear guidance of the x-axis, the structure has remained mechanically largely the same as the S9.
A short summary (further data can also be found in the advertising images):
The motherboard has been changed from the S6/S9 models, it is now controlled by an ESP32 chip. Especially for tinkerers to note: the ESP chips work with 3.3V voltage. When connecting 5V hardware, you should pay close attention! The board also provides 5V where needed. The layout has been largely retained, which makes it straightforward to retrofit it with old lasers. At first glance, it makes a better impression than the MKS DLC32 design.
The Air Assist nozzle is designed to be screwed onto the laser. Finally, it is fixed in place with a grub screw. Therefore, it cannot be used on the other lasers. By screwing, however, you also have no problems with the alignment of the nozzle, which should always be perfect.
As expected, the set-up is super easy. The instructions are top and also the small tricks in the setting of the mechanics are described. Nevertheless, I recommend going through the mentioned page and checking the mechanics carefully. It is not possible to adjust everything perfectly at factory production!
For me, the frame of the x-axis had shifted a bit due to the transport, so the long y-drive rod could no longer be rotated. If this is also the case for you, you can correct the alignment by loosening the screws on the upper profile:
I mounted the laser on a wooden plate and secured it with small holders before slipping (a wooden panel should not be used for safety reasons! For me, this construction is temporary and gets a metal plate as a support, so that the risk of fire is reduced!). The holders can be easily created yourself with the laser. Download here. [New: I was asked to provide an STL version as well, here it is: Link]. Afterwards, I lasered the work surface of the laser and attached small brackets to which I can attach workpieces. Another very nice feature are these printed heads for the small screws that make height adjustment very easy: Thingiverse
In addition, I attached a drag chain, as I still had it at hand. This helps against cable clutter. I prefer those that can be opened on the outside. The size is 10 × 15 mm, which is quite sufficient, but not if the air hose is still to be carried out.
Since I have become very accustomed to working with limit switches and reference runs, I had to retrofit them directly here. This works without further problems analogous to the S6/S9 (see also article about limit switches). For assembly, I printed small brackets (which are not particularly optimized, someone can certainly do that even better): https://www.thingiverse.com/thing:5392586. It should also be noted that the switches slightly reduce the work area, but it has not quite reached the advertised size before. A size of 385 × 390 mm is realistic with limit switches.
I have also become very accustomed to the fact that I do not have to switch on the pump manually, but have lasers do it themselves. This is also possible with the S10, but here with a small change to the S6/S9 (at least with the current version of the firmware).
To control the relay, you have to use the command M7, not as usual M8 (I think with further firmware versions this will also be improved / changed). It is also important that it is a high-level trigger relay, as you can not invert the pin here. For example: AliExpress link
Here I will collect the first tests and attempts from the other colleagues, so that you can get a good impression of the performance. Many of them can be found in the official Sculpfun User Group on Facebook. If a video is not done in English, you can turn on subtitles.
Here are some quick-and-dirty tests that I did by myself to test the laser. It’s not very structured yet, but provides a first impression.
Here is the link to the full review.
Article transferred from:https://wiki.the-iskens.com/documentation/sculpfun-s10-en/